Adrianli Hypersonic July 23, 2020 Share July 23, 2020 8 hours ago, boonhat_91 said: Hi all, I intend to move an existing wardrobe to the right of the door and unfortunately due to its dimensions the wardrobe left edge just about touches the right edge of the aircon remote, meaning my light switch will be blocked. Hence I also intend to relocate the light switch closer to the doorframe. A conventional switchplate is still too big, but today I learnt an 'architrave' switch is what I'm looking for! The thing is, I would like to relocate the switch as non-invasively as possible, so basically I will stick or screw in the new switch (with pattress box) in the area above the aircon remote. In this scenario I would have to run the wiring from where the existing switchplate is to the new switch 2-3cm away, running externally. My question is, is there enough length of wire behind the switchplate to do this, or do I need to extend the wires? Only when you open the switch then you will know. Very easy to open. ↡ Advertisement Link to post Share on other sites More sharing options...
Mustank Hypersonic July 23, 2020 Share July 23, 2020 8 hours ago, boonhat_91 said: Hi all, I intend to move an existing wardrobe to the right of the door and unfortunately due to its dimensions the wardrobe left edge just about touches the right edge of the aircon remote, meaning my light switch will be blocked. Hence I also intend to relocate the light switch closer to the doorframe. A conventional switchplate is still too big, but today I learnt an 'architrave' switch is what I'm looking for! The thing is, I would like to relocate the switch as non-invasively as possible, so basically I will stick or screw in the new switch (with pattress box) in the area above the aircon remote. In this scenario I would have to run the wiring from where the existing switchplate is to the new switch 2-3cm away, running externally. My question is, is there enough length of wire behind the switchplate to do this, or do I need to extend the wires? Use wifi switch Least effort Smart Life / Tuya WiFi 2.4GHz + RF433 Smart Wall Switch UK - Neutral Wiring Not Required - Compatible with Google Home & Amazon Alexa - Available in 1, 2, 3 Gang https://s.lazada.sg/s.rdiU 3 Link to post Share on other sites More sharing options...
Volvobrick Supersonic July 23, 2020 Share July 23, 2020 (edited) 15 minutes ago, Mustank said: Use wifi switch Least effort Smart Life / Tuya WiFi 2.4GHz + RF433 Smart Wall Switch UK - Neutral Wiring Not Required - Compatible with Google Home & Amazon Alexa - Available in 1, 2, 3 Gang https://s.lazada.sg/s.rdiU I have plenty of these (about 10 Sonoff ones - very cheap on Shopee nowadays). RF control is a must. But the switch will be behind the wardrobe, thus a hole will need to be cut for access or to mount the wifi switch. One limiting factor is, there must be a neutral wire in the box for the Wi-Fi switch to work. This is unlikely as normally you only see Live wires for light switches. Edited July 23, 2020 by Volvobrick 1 Link to post Share on other sites More sharing options...
Watwheels Supersonic July 23, 2020 Share July 23, 2020 Is your wardrobe sliding door type? Just saw a square hole at the back of the wardrobe where the switch is can liao what. Then place your wardrobe over the switch. It becomes a hidden switch. No need to play with wires. 😂 1 1 Link to post Share on other sites More sharing options...
Mustank Hypersonic July 23, 2020 Share July 23, 2020 4 minutes ago, Volvobrick said: I have plenty of these (about 10 Sonoff ones - very cheap on Shopee nowadays). RF control is a must. But the switch will be behind the wardrobe, thus a hole will need to be cut for access or to mount the wifi switch. No need what before he move the wardrobe, change it. Then move the wardrobe lor but if the switch spoil, then he thng kor 2 Link to post Share on other sites More sharing options...
Lala81 Hypersonic July 23, 2020 Share July 23, 2020 25 minutes ago, Watwheels said: Is your wardrobe sliding door type? Just saw a square hole at the back of the wardrobe where the switch is can liao what. Then place your wardrobe over the switch. It becomes a hidden switch. No need to play with wires. 😂 lizard can also go take nap inside wardrobe Link to post Share on other sites More sharing options...
boonhat_91 6th Gear July 23, 2020 Share July 23, 2020 2 hours ago, Watwheels said: Is your wardrobe sliding door type? Just saw a square hole at the back of the wardrobe where the switch is can liao what. Then place your wardrobe over the switch. It becomes a hidden switch. No need to play with wires. 😂 Then every time I want to on the light I need to open the wardrobe haha It's not the sliding door type - btw what is 'normal-opening-type' called ah 😅 Link to post Share on other sites More sharing options...
boonhat_91 6th Gear July 23, 2020 Share July 23, 2020 2 hours ago, Adrianli said: Only when you open the switch then you will know. Very easy to open. Of course, but I would prefer to do everything in one sitting. Don't want to go through the trouble of opening first then sian half if realise that I need to go buy extension wires. On that note, extension wire need to look for a certain type? Or any kind of electric wire will do? Link to post Share on other sites More sharing options...
Fcw75 Hypersonic July 23, 2020 Share July 23, 2020 2 minutes ago, boonhat_91 said: Of course, but I would prefer to do everything in one sitting. Don't want to go through the trouble of opening first then sian half if realise that I need to go buy extension wires. On that note, extension wire need to look for a certain type? Or any kind of electric wire will do? Just find an electrician to solve the problem for you. Some money cannot save one. 1 Link to post Share on other sites More sharing options...
Volvobrick Supersonic July 23, 2020 Share July 23, 2020 8 minutes ago, boonhat_91 said: Of course, but I would prefer to do everything in one sitting. Don't want to go through the trouble of opening first then sian half if realise that I need to go buy extension wires. On that note, extension wire need to look for a certain type? Or any kind of electric wire will do? Just grab some old cords for kettle/rice cooker and strip out the inner wires. That's more than enough thickness. Lights use very little current compared to kitchen appliances. You go to the shop and buy 10 cm of wires they also very sian selling to you! 1 4 Link to post Share on other sites More sharing options...
Stratovarius Turbocharged July 23, 2020 Share July 23, 2020 12 hours ago, boonhat_91 said: Hi all, I intend to move an existing wardrobe to the right of the door and unfortunately due to its dimensions the wardrobe left edge just about touches the right edge of the aircon remote, meaning my light switch will be blocked. Hence I also intend to relocate the light switch closer to the doorframe. A conventional switchplate is still too big, but today I learnt an 'architrave' switch is what I'm looking for! The thing is, I would like to relocate the switch as non-invasively as possible, so basically I will stick or screw in the new switch (with pattress box) in the area above the aircon remote. In this scenario I would have to run the wiring from where the existing switchplate is to the new switch 2-3cm away, running externally. My question is, is there enough length of wire behind the switchplate to do this, or do I need to extend the wires? The wires are concealed, but likely to come from the ceiling. Since you are moving up the switch, you might have enough wire. An estimation I usually use is if you are shifting the switch say, 3inches to the right, you need to move the also move the switch at least 3 inches up to use the length of same wire. Just curious how you going to run the wires within the wall? You can use a terminal block to extend the wire easily if you can cut a groove in the wall. Link to post Share on other sites More sharing options...
Mkl22 Twincharged July 23, 2020 Share July 23, 2020 12 hours ago, Volvobrick said: You need to open up the current one to check the spare length. You can always use some crimp connectors to extend (more secured since it will be behind the wardrobe). Avoid using the screw-type connector since it will not be accessible when it rusts. Alternatively if the wires come from the ceiling, move the new switch higher up and re-route the existing wires higher too. Crimp connectors should be the easiest though. You can even consider mounting the existing switch on the side of the new wardrobe running the wires inside. Your carpenter will have to cover the back properly though. I would follow your last option and mount the switch on the cupboard. Cleanest and still easy to access the wall portion If really need to. 1 Link to post Share on other sites More sharing options...
t0y0ta Supercharged July 23, 2020 Share July 23, 2020 12 hours ago, boonhat_91 said: Hi all, I intend to move an existing wardrobe to the right of the door and unfortunately due to its dimensions the wardrobe left edge just about touches the right edge of the aircon remote, meaning my light switch will be blocked. Hence I also intend to relocate the light switch closer to the doorframe. A conventional switchplate is still too big, but today I learnt an 'architrave' switch is what I'm looking for! The thing is, I would like to relocate the switch as non-invasively as possible, so basically I will stick or screw in the new switch (with pattress box) in the area above the aircon remote. In this scenario I would have to run the wiring from where the existing switchplate is to the new switch 2-3cm away, running externally. My question is, is there enough length of wire behind the switchplate to do this, or do I need to extend the wires? Another way is to 1) dismantle the existing light switch panel, leave the wires dangling first 2) Install the cabinets in their desired position, allowing the wires to dangle out on the side 3) wire/install the new small light switch on the side of the cabinet instead 1 Link to post Share on other sites More sharing options...
Dafansu Turbocharged July 23, 2020 Share July 23, 2020 (edited) get an electrician to pull out existing and do a box type. U might not be able to conceal back in the wall above the aircon remote area cause of the door frame sill. electrician can still drill a hole to run the cable from the back of the box. Edited July 23, 2020 by Dafansu Link to post Share on other sites More sharing options...
Othello Supersonic July 23, 2020 Share July 23, 2020 13 hours ago, boonhat_91 said: Hi all, I intend to move an existing wardrobe to the right of the door and unfortunately due to its dimensions the wardrobe left edge just about touches the right edge of the aircon remote, meaning my light switch will be blocked. Hence I also intend to relocate the light switch closer to the doorframe. A conventional switchplate is still too big, but today I learnt an 'architrave' switch is what I'm looking for! The thing is, I would like to relocate the switch as non-invasively as possible, so basically I will stick or screw in the new switch (with pattress box) in the area above the aircon remote. In this scenario I would have to run the wiring from where the existing switchplate is to the new switch 2-3cm away, running externally. My question is, is there enough length of wire behind the switchplate to do this, or do I need to extend the wires? 25 minutes ago, Mkl22 said: I would follow your last option and mount the switch on the cupboard. Cleanest and still easy to access the wall portion If really need to. I agree. Mount the switch on the wardrobe. Less headache and much nicer. The wiring are concealed, no way it will look nice if you mount the new switch on the wall. Of cos, they can drill hole to conceal the wire ...... Usually the wires still got freeplay one, it should be enough without the need to join wires. Link to post Share on other sites More sharing options...
boonhat_91 6th Gear July 23, 2020 Share July 23, 2020 36 minutes ago, Mkl22 said: I would follow your last option and mount the switch on the cupboard. Cleanest and still easy to access the wall portion If really need to. 8 minutes ago, Othello said: I agree. Mount the switch on the wardrobe. Less headache and much nicer. Just to clarify, my wardrobe in question is those standalone ikea type, not carpentry built-in one. So mounting the switch on the cupboard is not my top choice, though I have considered as well. 1 Link to post Share on other sites More sharing options...
boonhat_91 6th Gear July 23, 2020 Share July 23, 2020 23 minutes ago, t0y0ta said: Another way is to 1) dismantle the existing light switch panel, leave the wires dangling first 2) Install the cabinets in their desired position, allowing the wires to dangle out on the side 3) wire/install the new small light switch on the side of the cabinet instead Yes, thanks for the description! Basically my question is whether there will be enough length of existing wire able to dangle out on the side, so that I can install the new switch either a few cm to the left or on the side of the cabinet. Link to post Share on other sites More sharing options...
Dafansu Turbocharged July 23, 2020 Share July 23, 2020 1 minute ago, boonhat_91 said: Yes, thanks for the description! Basically my question is whether there will be enough length of existing wire able to dangle out on the side, so that I can install the new switch either a few cm to the left or on the side of the cabinet. usually need to extend the wiring. likely u need to install box version as can't drill a hole in the wall. ↡ Advertisement 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In NowRelated Discussions
Related Discussions
Simple home DIY repairs
Simple home DIY repairs
Going to Brisbane, Please Advice
Going to Brisbane, Please Advice
Even after $60k in vet bills and going into debt, S’pore couple couldn’t save their dog
Even after $60k in vet bills and going into debt, S’pore couple couldn’t save their dog
Advice for accident
Advice for accident
Advice needed: 6 days in Perth with a two year old and farm stay in March?
Advice needed: 6 days in Perth with a two year old and farm stay in March?
Ageing and Home Safety - Tech That Detects Falls
Ageing and Home Safety - Tech That Detects Falls
Grinding racket
Grinding racket
Dream home
Dream home