Jump to content

THINKWARE / INAVI Users, Come In

Maxus-MIFA9

By Maxus-MIFA9,
in Accessories

 Share

Recommended Posts

CultureShock

CultureShock

1st Gear

Two possible reasons for the cutoff:

 

1. Your F750 cutoff voltage is set high? Here's a link to a good article with an informative voltage cutoff table... https://dashcamtalk.com/battery-discharge-prevention/

 

2. According to the Infiniti specs, the Q50 has a 'battery saver' function. That could have cut off the power?

 

As for battery, you can get the Lukas LK-530-12V or the Blackvue Cellink B. They should work.

 

Share your experience with the F750. I'm also thinking of getting it for my Q50 soon.

 

 

 

Did you get the Thinkware and hook up to a power cell successfully? It's been almost a month and ZMC hasn't responded to my PM for their contacts.... :pissed-off:

Link to post
Share on other sites
tchn

tchn

1st Gear

I didn't have an F750 to try, but reading the specification... it needs to be connected to ACC and B+ at the fusebox. Once it notices ACC is off, it will draw power from B+ and go into parking mode. If you connect a battery, it will stay constantly in drive mode.

 

I went with the DR650 instead, because it goes into parking mode after a short interval once the vehicle is stopped. I currently have the 1CH, and will wait until Blackvue has FHD for its rear camera before I upgrade to 2CH.

 

Did you get the Thinkware and hook up to a power cell successfully? It's been almost a month and ZMC hasn't responded to my PM for their contacts.... :pissed-off:

 

Link to post
Share on other sites
CultureShock

CultureShock

1st Gear

I didn't have an F750 to try, but reading the specification... it needs to be connected to ACC and B+ at the fusebox. Once it notices ACC is off, it will draw power from B+ and go into parking mode. If you connect a battery, it will stay constantly in drive mode.

 

I went with the DR650 instead, because it goes into parking mode after a short interval once the vehicle is stopped. I currently have the 1CH, and will wait until Blackvue has FHD for its rear camera before I upgrade to 2CH.

 

 

I see. Looks like my Thinkware's parking mode is going to be a dud. :lll._.: and ZMC's non-response is not helping either!!

Link to post
Share on other sites
Charmet

Charmet

3rd Gear

Did you get the Thinkware and hook up to a power cell successfully? It's been almost a month and ZMC hasn't responded to my PM for their contacts.... :pissed-off:

 

You're not the only one Bro. I also asked ZMC via PM about Cellink B installation and there has been no reply.

 

Looks like they are not interested in our business, and the business of new customers.

 

The product is good, but the service leaves much to be desired.

Link to post
Share on other sites
CultureShock

CultureShock

1st Gear

 

You're not the only one Bro. I also asked ZMC via PM about Cellink B installation and there has been no reply.

 

Looks like they are not interested in our business, and the business of new customers.

 

The product is good, but the service leaves much to be desired.

Maybe they're hoping you'll give up asking if they remain silent.... :lll._.:

Link to post
Share on other sites
Thinkwaresg

Thinkwaresg

1st Gear

Hi guys

 

thank you so much for your queries , however this is not our main form of contact . Therefore we strongly suggest if you have any questions , please kindly call us at 65553560 or email us at [email protected] .

 

our office is closed from 3rd - 6th september 2015 due to the COMEX show.

 

All your queries are important to us, and we always hope to be of best service to you .

 

We will continue working hard to be the best dash cam brand in korea and the world .

 

thank you and hope to hear from you guys soon . =)

Link to post
Share on other sites
Thinkbig

Thinkbig

Neutral Newbie
Hi Guys and Gals,
Anyone installed Thinkware's cameras (ie F750 or similar)? Would like to know how good is the Road Safety Warning System (Front Collision) and Safety Camera Alert (Speed Camera & photo enforcement locations).
Thank you in advance for sharing :)

Link to post
Share on other sites
Skywire01

Skywire01

1st Gear
(edited)

Maybe they're hoping you'll give up asking if they remain silent.... :lll._.:

 

ZMC is the distributor for thinkware products. Normally if a local distributor sucks on the after-sales service, i'll go direct to the HQ to check with them for my queries and also let them know why i'm not getting any answers from the local distributor and the type of quality i'm encountering after buying their products.

 

If language is a barrier, we can alway type in English and use google translations to Korean!

 

My 2 cents.

Edited by Skywire01
Link to post
Share on other sites
AnsonHo

AnsonHo

Clutched

 

Hi Guys and Gals,
Anyone installed Thinkware's cameras (ie F750 or similar)? Would like to know how good is the Road Safety Warning System (Front Collision) and Safety Camera Alert (Speed Camera & photo enforcement locations).
Thank you in advance for sharing :)

 

 

 

I am very interested in F750 too. Does the safety camera alert work in Singapore?

Link to post
Share on other sites
Annapurna

Annapurna

1st Gear

I just had the X500 installed this morning. I tried to install the PC Viewer software that is supposed to be from the MicroSD card but I cannot locate the file from the card. May I know where I can download a copy of the PC Viewer software? Also what is the recommended voltage cutoff setting? The current default setting is 12.2V.

Link to post
Share on other sites
Furrynadz

Furrynadz

5th Gear

thinkware.com.sg


 

I am very interested in F750 too. Does the safety camera alert work in Singapore?

 

 

yes

 

there is a new dashboard player/firmware/cam data just dated 7 sept...fresh

Link to post
Share on other sites
CultureShock

CultureShock

1st Gear

thinkware.com.sg

 

 

yes

 

there is a new dashboard player/firmware/cam data just dated 7 sept...fresh

Why is it that they don't show details of the updates, so that users can determine if they really want to update the firmware or if it's worth updating? :nosepick:

Link to post
Share on other sites
Annapurna

Annapurna

1st Gear

I just had the X500 installed this morning. I tried to install the PC Viewer software that is supposed to be from the MicroSD card but I cannot locate the file from the card. May I know where I can download a copy of the PC Viewer software? Also what is the recommended voltage cutoff setting? The current default setting is 12.2V.

 

Anyone can help on this? Thanks.

Link to post
Share on other sites
Furrynadz

Furrynadz

5th Gear

Why is it that they don't show details of the updates, so that users can determine if they really want to update the firmware or if it's worth updating? :nosepick:

just update la....scare wat...

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
×
×
  • Create New...