Jump to content

ICE MEETUP ON WEDNESDAY, 5TH APRIL


Headshok
 Share

Recommended Posts

(edited)

HI GUYS,

 

ICE meetup is on tomorrow, but instead of the usual NASI PADANG place, it'll be held at a different location.

 

this time meetup is at a pub(thus got alcohol), so pple can enjoy

 

here's the address:

Koon Kee Restaurant & Pub

6 Yio Chu Kang Road

 

tel:62881206,

 

attached is a map

 

meetup will be from 930pm onwards lah... if unsure who is who, approach the pub owner and ask abt the meetup lah

 

 

 

Cheers!

post-4-1144070135_thumb.jpg

Edited by Headshok
↡ Advertisement
Link to post
Share on other sites

Neutral Newbie

Hey Headshok!

Take some photos of the meeting place tmr, attach the map and ask th moderator to make the meet-up location a sticky [thumbsup]

You going for another movie and going over after the movie for the meetup isit??? [sly]

Link to post
Share on other sites

Neutral Newbie

I went there for lunch last Friday, but din see Leo ard... wanted to say [wave] to him cos not been attending meetups often enuf lately due to heavy workload [sweatdrop]

Link to post
Share on other sites

Neutral Newbie

There is where? The Nasi Padang place? Leo is usually there only in the evenings.

For lunch, look for him at the canteen in MacTech Building, Kallang Pudding Road. [;)]

Link to post
Share on other sites

HI GUYS,

 

ICE meetup is on tomorrow, but instead of the usual NASI PADANG place, it'll be held at a different location.

 

this time meetup is at a pub(thus got alcohol), so pple can enjoy

 

here's the address:

Koon Kee Restaurant & Pub

6 Yio Chu Kang Road

 

tel:62881206,

 

attached is a map

 

meetup will be from 930pm onwards lah... if unsure who is who, approach the pub owner and ask abt the meetup lah

 

 

 

Cheers!

 

 

 

 

 

 

 

 

 

 

so is it still ON tonight>> [gossip]

Link to post
Share on other sites

Neutral Newbie

Hi HeadShok and Kwongwing.

 

Met both of you in ECP meetup. Wonder you remmeber me anot.

I need some advise from you.

 

My current setup consist of the below in my integra. Anyone can advise me on what to upgrade. Currently the bass is not tight as what I would have expected. I was thinking to switch the soundstream amp to power the front and the infinity amp to power the rear. Any advise? Or is it tuning problem?

How much power do I need to power up my 10inch?

 

Clarion 956

 

Infinity Beta Digital 100for front speakers

With 100 watts RMS per channel in stereo mode (or a bruising 400 watts RMS in mono), this versatile Beta amp is ready to work.

stereo, bridged mono or Tri-way output

2-ohm stable in stereo (4-ohm bridged)

MOSFET power supply

digital Class D amplifier

gold-plated preamp inputs

balanced differential inputs help keep noise away

Uniblock heat sink provides superb heat dissipation and RF shielding to help keep away radio frequency interference

set-screw terminals for crimpless wire connections

muting circuit prevents turn-on thump

signal-to-noise ratio 90 dB

power at 2 ohms 200 watts RMS x 2

variable (0-11 dB) bass boost at 40 Hz

frequency response 20-20,000 Hz

11-7/8"W x 2-3/16"H x 8-9/16"D

 

 

CDT62

 

SoundStream PIC 2.240for sub

 

Maximum power, W (14,4 v, k.n.i. = 1%, 4 Om/2 Ohm) 72,3/99,4

Coefficient of nonlinear distortions, % (1 kHz, P = of 0,1 Pmax, 4 Om/2 Ohm) 0,034/0,036

Input sensitivity, into 0,16 - 6,3

Signal-to-noise ratio is, dBA 92,5

Crosstalk attenuation, dB (1 kHz) 62

Frequency band, Hz (+0/-ydB) 4 - 41000

Speed of the growth of signal on output, V/ s 10

 

Soundstream Exact 10 Subwoofers

Link to post
Share on other sites

ur sub should be 400 rms. one of our kaki using a pair of those too.

 

drop by this wednesday, it'll be easier to discuss lah..

↡ Advertisement
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...